Ipox IP-4MTI2H Bug report...
Moderator: Rio71
Ipox IP-4MTI2H Bug report...
So, nach einigem herumprobieren mit dem Board, habe ich mal eine kleine Bugliste, die ich noch erweitern werde. Ich habe das auf Englisch gehalten, da ich das auch an Taiwan weiterschicke.
BUGs:
1) Does the IP-4MTI2H support Speedstep? CPU is always running at full speed (which is not the sense of Centrino based systems I think). Maybe fixed in an upcoming BIOS release supporting it?
2) No option in the BIOS to disable the onBoard SATA-Controller (SI3112). Maybe fixed in a new BIOS release?
3) When onBoard LAN controller is configured with a fixed IP, the LAN controller is unworkable on reboot. Disabling and reenabling solves the problem.
4) When configuring a temperature warning in BIOS above 56°C it will ignore the setting and choose at maximum 56°C.
5) onBoard SI3112A Raid-Controller seems unstable. Unconfirmed and still testing.
Some quality issues:
1) In further revision there should be used better capacitors! There is already one capacitor coming up (not broken but pumped up). I would not reccomend this configuration in higher temperature industrial environments.
2) The onboard sound has big quality defects. There is a lot of noise in playback mode (you can even hear your DVD-Rom spin up and HDD-drive when it seeks).
3) Mainboard is not delivered with a driver floppy containing the SI3112 drivers for XP/2000/NT. When installing XP or 2k to a SATA drive attached to the onBoard SI3112 this driver is needed on a floppy (Microsoft does not support drivers on CD at this point of setup).
4) The manual has some errors (e.g. Auto power Jumper P6 is labeled as ACPI on).
BUGs:
1) Does the IP-4MTI2H support Speedstep? CPU is always running at full speed (which is not the sense of Centrino based systems I think). Maybe fixed in an upcoming BIOS release supporting it?
2) No option in the BIOS to disable the onBoard SATA-Controller (SI3112). Maybe fixed in a new BIOS release?
3) When onBoard LAN controller is configured with a fixed IP, the LAN controller is unworkable on reboot. Disabling and reenabling solves the problem.
4) When configuring a temperature warning in BIOS above 56°C it will ignore the setting and choose at maximum 56°C.
5) onBoard SI3112A Raid-Controller seems unstable. Unconfirmed and still testing.
Some quality issues:
1) In further revision there should be used better capacitors! There is already one capacitor coming up (not broken but pumped up). I would not reccomend this configuration in higher temperature industrial environments.
2) The onboard sound has big quality defects. There is a lot of noise in playback mode (you can even hear your DVD-Rom spin up and HDD-drive when it seeks).
3) Mainboard is not delivered with a driver floppy containing the SI3112 drivers for XP/2000/NT. When installing XP or 2k to a SATA drive attached to the onBoard SI3112 this driver is needed on a floppy (Microsoft does not support drivers on CD at this point of setup).
4) The manual has some errors (e.g. Auto power Jumper P6 is labeled as ACPI on).
Server: Intel Pentium-M 1.60 GHz on DFI i855GME-MGF, 1 GB DDR-333 Kingston ValueRam, Yeon Yang 0420 Cube
Gaming: Intel Pentium-M 1.40GHz @ 1,87GHz on ASUS P4GPL-X, 512 MB DDR-433 Kingston HyperX, GeForce 6800GT, Lian LI PC-62
HTPC: Intel Pentium-M 1.50 GHz [passive] on Ipox 4MTI2H, 512 MB DDR-333 Infineon 3rd, Antec Aria Mini-Cube, VDR with dual DVB-T/-C
Gaming: Intel Pentium-M 1.40GHz @ 1,87GHz on ASUS P4GPL-X, 512 MB DDR-433 Kingston HyperX, GeForce 6800GT, Lian LI PC-62
HTPC: Intel Pentium-M 1.50 GHz [passive] on Ipox 4MTI2H, 512 MB DDR-333 Infineon 3rd, Antec Aria Mini-Cube, VDR with dual DVB-T/-C
Jo, ein paar Bugs hat meins auch, aber alles kleine Sachen. S-ATA und Raid hab ich nicht.
Ton haut alles hin.
Wenn ich ne PCI-VGA reinstecke, denkt Win XP es ist eine PCI-Ethernet und disabled den Onboard LAN-Chip. Immer sehr ärgerlich wegen komplette Neuinstallation aller LAN-Treiber einschl. Konfig.
Aber mit der PCI-VGA war nur zu Anfang zum probieren und benchen.
Sonst bis auf ein paar Handbuch-Jumper Schnitzer gehts. Über mangelnde Spannungsversorgung etc. habe ich mir bisher keinen Kopf zerbrochen.
@Franzose: Power on Switch bei Dir richtig belegt?
Ton haut alles hin.
Wenn ich ne PCI-VGA reinstecke, denkt Win XP es ist eine PCI-Ethernet und disabled den Onboard LAN-Chip. Immer sehr ärgerlich wegen komplette Neuinstallation aller LAN-Treiber einschl. Konfig.
Aber mit der PCI-VGA war nur zu Anfang zum probieren und benchen.
Sonst bis auf ein paar Handbuch-Jumper Schnitzer gehts. Über mangelnde Spannungsversorgung etc. habe ich mir bisher keinen Kopf zerbrochen.
@Franzose: Power on Switch bei Dir richtig belegt?
Hauptsystem:
HP tc4400 tablet pc
Büro@Home:
Asus P4P800-SE mit CT479
Pentium M 1500 (Banias)
512MB DDR 333
GF4 MX
SB-Live
Wohnzimmer:
Baustelle
HP tc4400 tablet pc
Büro@Home:
Asus P4P800-SE mit CT479
Pentium M 1500 (Banias)
512MB DDR 333
GF4 MX
SB-Live
Wohnzimmer:
Baustelle
Ja, nur der Auto Power on ist im Handbuch als ACPI on bezeichnet.marumpel wrote:@Franzose: Power on Switch bei Dir richtig belegt?
Wie sieht es bei dir mit Speedstep aus?
Server: Intel Pentium-M 1.60 GHz on DFI i855GME-MGF, 1 GB DDR-333 Kingston ValueRam, Yeon Yang 0420 Cube
Gaming: Intel Pentium-M 1.40GHz @ 1,87GHz on ASUS P4GPL-X, 512 MB DDR-433 Kingston HyperX, GeForce 6800GT, Lian LI PC-62
HTPC: Intel Pentium-M 1.50 GHz [passive] on Ipox 4MTI2H, 512 MB DDR-333 Infineon 3rd, Antec Aria Mini-Cube, VDR with dual DVB-T/-C
Gaming: Intel Pentium-M 1.40GHz @ 1,87GHz on ASUS P4GPL-X, 512 MB DDR-433 Kingston HyperX, GeForce 6800GT, Lian LI PC-62
HTPC: Intel Pentium-M 1.50 GHz [passive] on Ipox 4MTI2H, 512 MB DDR-333 Infineon 3rd, Antec Aria Mini-Cube, VDR with dual DVB-T/-C
Eigentlich ganz easy im WIndows einzustellen. Hab aber momentan keine HDD drin in meinem IPOX-System, wird aber die Woche erledigt sein dann schaue ich mal. Hatte aber bis dato immer nur 100% Speed laufen lassen....
Sobald ich was hab´schreib ich es hier rein.
Sobald ich was hab´schreib ich es hier rein.
Hauptsystem:
HP tc4400 tablet pc
Büro@Home:
Asus P4P800-SE mit CT479
Pentium M 1500 (Banias)
512MB DDR 333
GF4 MX
SB-Live
Wohnzimmer:
Baustelle
HP tc4400 tablet pc
Büro@Home:
Asus P4P800-SE mit CT479
Pentium M 1500 (Banias)
512MB DDR 333
GF4 MX
SB-Live
Wohnzimmer:
Baustelle
-
- Tiefschürfender Techniker
- Posts: 9923
- Joined: 01.04.2002 - 02:00
- Location: Residenz des Rechts
- Contact:
da ist ja noch etwas arbeit zu erledigen..
bei quality 1) macht sich nen bild immer ganz gut.
ist dieser evl gar verkertherum eingelötet ?
bei quality 1) macht sich nen bild immer ganz gut.
ist dieser evl gar verkertherum eingelötet ?
- SMPS ; PWM ; BUCK ; BOOST ; SEPIC basteln... :: KHV basteln... ; E85 im E34
- P4 2.8C @ 3208 (SL6Z5) :: IHS plan :: 1,600V wakü :: 4x256MB BH-5 DDR401 2-2-2-6 :: IS7-E , mod
R 8500 @ 295/295--> DVI --> EIZO 15" TFT :: CMI 8738/PCI-6ch-LX :: T7K250
LG GSA-H10N :: Blue Storm II 350 :: CS-601 :: T-DSL 3Mbit :: 98SE/XP :: Details
- P4 2.4C @ 3350 (SL6Z3) :: 1,55V :: Alpha PAL8942 :: DDR480 2,5-2-2-6 :: IC7 , mod
- P4 2.4B @ 3150 (SL6RZ) :: 1,65V MCX4000 + 90'er :: DDR466 2-2-2-5-infinite-64µs :: 4GEA :: IHS off
- Laptop PIII 700@700 (100FSB/440BX) :: 256MB :: 18Gig Toshiba :: 4MB ATI :: 14,1" TFT :: Win98SE
* Fußnote: 90% aller Computerprobleme findet man zwischen Stuhl und Tastatur. ;-)
Wie kann man einen Kondensator verkehrt herum einlöten???Rio71 wrote:ist dieser evl gar verkertherum eingelötet ?
Server: Intel Pentium-M 1.60 GHz on DFI i855GME-MGF, 1 GB DDR-333 Kingston ValueRam, Yeon Yang 0420 Cube
Gaming: Intel Pentium-M 1.40GHz @ 1,87GHz on ASUS P4GPL-X, 512 MB DDR-433 Kingston HyperX, GeForce 6800GT, Lian LI PC-62
HTPC: Intel Pentium-M 1.50 GHz [passive] on Ipox 4MTI2H, 512 MB DDR-333 Infineon 3rd, Antec Aria Mini-Cube, VDR with dual DVB-T/-C
Gaming: Intel Pentium-M 1.40GHz @ 1,87GHz on ASUS P4GPL-X, 512 MB DDR-433 Kingston HyperX, GeForce 6800GT, Lian LI PC-62
HTPC: Intel Pentium-M 1.50 GHz [passive] on Ipox 4MTI2H, 512 MB DDR-333 Infineon 3rd, Antec Aria Mini-Cube, VDR with dual DVB-T/-C
-
- Tiefschürfender Techniker
- Posts: 9923
- Joined: 01.04.2002 - 02:00
- Location: Residenz des Rechts
- Contact:
...
da er nur zwei anschlüsse hat wird die auswahl eng...
da er nur zwei anschlüsse hat wird die auswahl eng...
- SMPS ; PWM ; BUCK ; BOOST ; SEPIC basteln... :: KHV basteln... ; E85 im E34
- P4 2.8C @ 3208 (SL6Z5) :: IHS plan :: 1,600V wakü :: 4x256MB BH-5 DDR401 2-2-2-6 :: IS7-E , mod
R 8500 @ 295/295--> DVI --> EIZO 15" TFT :: CMI 8738/PCI-6ch-LX :: T7K250
LG GSA-H10N :: Blue Storm II 350 :: CS-601 :: T-DSL 3Mbit :: 98SE/XP :: Details
- P4 2.4C @ 3350 (SL6Z3) :: 1,55V :: Alpha PAL8942 :: DDR480 2,5-2-2-6 :: IC7 , mod
- P4 2.4B @ 3150 (SL6RZ) :: 1,65V MCX4000 + 90'er :: DDR466 2-2-2-5-infinite-64µs :: 4GEA :: IHS off
- Laptop PIII 700@700 (100FSB/440BX) :: 256MB :: 18Gig Toshiba :: 4MB ATI :: 14,1" TFT :: Win98SE
* Fußnote: 90% aller Computerprobleme findet man zwischen Stuhl und Tastatur. ;-)
Explodieren Elkos nicht direkt, wenn man sie verpolt? Ich hab hier noch nen Satz tote Elkos von nem MSI 815EPT Pro, mal ausprobieren...
PS: Auf jeden Fall wirds lustig, wenn man mit ner Loetlampe draufhaelt, ich haette nicht gedacht, dass so kleine Elkos (auf ner toten GF2MX) so einen Rumms machen koennen.
PS: Auf jeden Fall wirds lustig, wenn man mit ner Loetlampe draufhaelt, ich haette nicht gedacht, dass so kleine Elkos (auf ner toten GF2MX) so einen Rumms machen koennen.
-
- Tiefschürfender Techniker
- Posts: 9923
- Joined: 01.04.2002 - 02:00
- Location: Residenz des Rechts
- Contact:
im prinzip schon..
aber manchmal pfeifen sie auch nur ab oder auch unten am verschluß vorbei.
könnte sein, der druck hat sich aufgebaut und dann unten abgepfiffen.
möglicherweise nen produktionsfehler, bei welchem der/die elkos falschherum in den robotergriffel geraten sind.
nen so früher ausfall durch aufblasen ist schon sehr sehr ungewöhnlich.
aber manchmal pfeifen sie auch nur ab oder auch unten am verschluß vorbei.
könnte sein, der druck hat sich aufgebaut und dann unten abgepfiffen.
möglicherweise nen produktionsfehler, bei welchem der/die elkos falschherum in den robotergriffel geraten sind.
nen so früher ausfall durch aufblasen ist schon sehr sehr ungewöhnlich.
- SMPS ; PWM ; BUCK ; BOOST ; SEPIC basteln... :: KHV basteln... ; E85 im E34
- P4 2.8C @ 3208 (SL6Z5) :: IHS plan :: 1,600V wakü :: 4x256MB BH-5 DDR401 2-2-2-6 :: IS7-E , mod
R 8500 @ 295/295--> DVI --> EIZO 15" TFT :: CMI 8738/PCI-6ch-LX :: T7K250
LG GSA-H10N :: Blue Storm II 350 :: CS-601 :: T-DSL 3Mbit :: 98SE/XP :: Details
- P4 2.4C @ 3350 (SL6Z3) :: 1,55V :: Alpha PAL8942 :: DDR480 2,5-2-2-6 :: IC7 , mod
- P4 2.4B @ 3150 (SL6RZ) :: 1,65V MCX4000 + 90'er :: DDR466 2-2-2-5-infinite-64µs :: 4GEA :: IHS off
- Laptop PIII 700@700 (100FSB/440BX) :: 256MB :: 18Gig Toshiba :: 4MB ATI :: 14,1" TFT :: Win98SE
* Fußnote: 90% aller Computerprobleme findet man zwischen Stuhl und Tastatur. ;-)
Wie gesagt, er ist noch nicht ausgefallen bei mir, nur die Sollbruchstellen oben haben sich schon gewölbt und es ist ein wenig Elektrolyt ausgeflossen. Habe das gesäubert, seitdem ist nichts mehr nachgekommen.Rio71 wrote:möglicherweise nen produktionsfehler, bei welchem der/die elkos falschherum in den robotergriffel geraten sind.
nen so früher ausfall durch aufblasen ist schon sehr sehr ungewöhnlich.
Server: Intel Pentium-M 1.60 GHz on DFI i855GME-MGF, 1 GB DDR-333 Kingston ValueRam, Yeon Yang 0420 Cube
Gaming: Intel Pentium-M 1.40GHz @ 1,87GHz on ASUS P4GPL-X, 512 MB DDR-433 Kingston HyperX, GeForce 6800GT, Lian LI PC-62
HTPC: Intel Pentium-M 1.50 GHz [passive] on Ipox 4MTI2H, 512 MB DDR-333 Infineon 3rd, Antec Aria Mini-Cube, VDR with dual DVB-T/-C
Gaming: Intel Pentium-M 1.40GHz @ 1,87GHz on ASUS P4GPL-X, 512 MB DDR-433 Kingston HyperX, GeForce 6800GT, Lian LI PC-62
HTPC: Intel Pentium-M 1.50 GHz [passive] on Ipox 4MTI2H, 512 MB DDR-333 Infineon 3rd, Antec Aria Mini-Cube, VDR with dual DVB-T/-C
-
- Tiefschürfender Techniker
- Posts: 9923
- Joined: 01.04.2002 - 02:00
- Location: Residenz des Rechts
- Contact:
genau das bezeichnet den ausfall dieses elkos.
die anderen müssen das jetzt mitstemmen.
die anderen müssen das jetzt mitstemmen.
- SMPS ; PWM ; BUCK ; BOOST ; SEPIC basteln... :: KHV basteln... ; E85 im E34
- P4 2.8C @ 3208 (SL6Z5) :: IHS plan :: 1,600V wakü :: 4x256MB BH-5 DDR401 2-2-2-6 :: IS7-E , mod
R 8500 @ 295/295--> DVI --> EIZO 15" TFT :: CMI 8738/PCI-6ch-LX :: T7K250
LG GSA-H10N :: Blue Storm II 350 :: CS-601 :: T-DSL 3Mbit :: 98SE/XP :: Details
- P4 2.4C @ 3350 (SL6Z3) :: 1,55V :: Alpha PAL8942 :: DDR480 2,5-2-2-6 :: IC7 , mod
- P4 2.4B @ 3150 (SL6RZ) :: 1,65V MCX4000 + 90'er :: DDR466 2-2-2-5-infinite-64µs :: 4GEA :: IHS off
- Laptop PIII 700@700 (100FSB/440BX) :: 256MB :: 18Gig Toshiba :: 4MB ATI :: 14,1" TFT :: Win98SE
* Fußnote: 90% aller Computerprobleme findet man zwischen Stuhl und Tastatur. ;-)
Noch ein Bug gefunden:
Manuelles Speichertiming RAS to CAS Delay im Bios wird ignoriert und immer auf 2 gesetzt.
Manuelles Speichertiming RAS to CAS Delay im Bios wird ignoriert und immer auf 2 gesetzt.
Server: Intel Pentium-M 1.60 GHz on DFI i855GME-MGF, 1 GB DDR-333 Kingston ValueRam, Yeon Yang 0420 Cube
Gaming: Intel Pentium-M 1.40GHz @ 1,87GHz on ASUS P4GPL-X, 512 MB DDR-433 Kingston HyperX, GeForce 6800GT, Lian LI PC-62
HTPC: Intel Pentium-M 1.50 GHz [passive] on Ipox 4MTI2H, 512 MB DDR-333 Infineon 3rd, Antec Aria Mini-Cube, VDR with dual DVB-T/-C
Gaming: Intel Pentium-M 1.40GHz @ 1,87GHz on ASUS P4GPL-X, 512 MB DDR-433 Kingston HyperX, GeForce 6800GT, Lian LI PC-62
HTPC: Intel Pentium-M 1.50 GHz [passive] on Ipox 4MTI2H, 512 MB DDR-333 Infineon 3rd, Antec Aria Mini-Cube, VDR with dual DVB-T/-C
-
- Tiefschürfender Techniker
- Posts: 9923
- Joined: 01.04.2002 - 02:00
- Location: Residenz des Rechts
- Contact:
haste punkt 2 quality mal mit nem anderen nt probiert ? könnte das problem beheben.
- SMPS ; PWM ; BUCK ; BOOST ; SEPIC basteln... :: KHV basteln... ; E85 im E34
- P4 2.8C @ 3208 (SL6Z5) :: IHS plan :: 1,600V wakü :: 4x256MB BH-5 DDR401 2-2-2-6 :: IS7-E , mod
R 8500 @ 295/295--> DVI --> EIZO 15" TFT :: CMI 8738/PCI-6ch-LX :: T7K250
LG GSA-H10N :: Blue Storm II 350 :: CS-601 :: T-DSL 3Mbit :: 98SE/XP :: Details
- P4 2.4C @ 3350 (SL6Z3) :: 1,55V :: Alpha PAL8942 :: DDR480 2,5-2-2-6 :: IC7 , mod
- P4 2.4B @ 3150 (SL6RZ) :: 1,65V MCX4000 + 90'er :: DDR466 2-2-2-5-infinite-64µs :: 4GEA :: IHS off
- Laptop PIII 700@700 (100FSB/440BX) :: 256MB :: 18Gig Toshiba :: 4MB ATI :: 14,1" TFT :: Win98SE
* Fußnote: 90% aller Computerprobleme findet man zwischen Stuhl und Tastatur. ;-)
Wie das?Rio71 wrote:haste punkt 2 quality mal mit nem anderen nt probiert ? könnte das problem beheben.
Server: Intel Pentium-M 1.60 GHz on DFI i855GME-MGF, 1 GB DDR-333 Kingston ValueRam, Yeon Yang 0420 Cube
Gaming: Intel Pentium-M 1.40GHz @ 1,87GHz on ASUS P4GPL-X, 512 MB DDR-433 Kingston HyperX, GeForce 6800GT, Lian LI PC-62
HTPC: Intel Pentium-M 1.50 GHz [passive] on Ipox 4MTI2H, 512 MB DDR-333 Infineon 3rd, Antec Aria Mini-Cube, VDR with dual DVB-T/-C
Gaming: Intel Pentium-M 1.40GHz @ 1,87GHz on ASUS P4GPL-X, 512 MB DDR-433 Kingston HyperX, GeForce 6800GT, Lian LI PC-62
HTPC: Intel Pentium-M 1.50 GHz [passive] on Ipox 4MTI2H, 512 MB DDR-333 Infineon 3rd, Antec Aria Mini-Cube, VDR with dual DVB-T/-C
So, hier einmal CBROM:
******** ti2h4624.BIN BIOS component ********
No. Item-Name Original-Size Compressed-Size Original-File-Name
================================================================================
0. System BIOS 20000h(128.00K) 12BD8h(74.96K) TI2H-014.BIN
1. XGROUP CODE 0CB60h(50.84K) 089B0h(34.42K) awardext.rom
2. ACPI table 04144h(16.32K) 01926h(6.29K) ACPITBL.BIN
3. EPA pattern 00046h(0.07K) 0006Dh(0.11K) AWARDEPA.BIN
4. YGROUP ROM 0EE20h(59.53K) 03B99h(14.90K) awardeyt.rom
5. Other(4029:0000) 04380h(16.88K) 01FA7h(7.91K) _EN_CODE.BIN
6. PCI driver[A] 0A800h(42.00K) 056BEh(21.69K) 4247.bin
7. PCI driver 0C000h(48.00K) 07190h(28.39K) BA1216Q2.lom
8. VGA ROM[1] 10000h(64.00K) 07F87h(31.88K) 164_3104.DAT
9. Other(402E:0000) 01470h(5.11K) 00783h(1.88K) 164_3104.BIN
10. Flash ROM 0ABD5h(42.96K) 05D84h(23.38K) AWDFLASH.EXE
Total compress code space = 4B000h(300.00K)
Total compressed code size = 3D737h(245.80K)
Remain compress code space = 0D8C9h(54.20K)
** Micro Code Information **
Update ID CPUID | Update ID CPUID | Update ID CPUID | Update ID CPUID
------------------+--------------------+--------------------+-------------------
SLOT2 17 0F29 |
D:\Treiber\IPOX4M~1>
******** ti2h4624.BIN BIOS component ********
No. Item-Name Original-Size Compressed-Size Original-File-Name
================================================================================
0. System BIOS 20000h(128.00K) 12BD8h(74.96K) TI2H-014.BIN
1. XGROUP CODE 0CB60h(50.84K) 089B0h(34.42K) awardext.rom
2. ACPI table 04144h(16.32K) 01926h(6.29K) ACPITBL.BIN
3. EPA pattern 00046h(0.07K) 0006Dh(0.11K) AWARDEPA.BIN
4. YGROUP ROM 0EE20h(59.53K) 03B99h(14.90K) awardeyt.rom
5. Other(4029:0000) 04380h(16.88K) 01FA7h(7.91K) _EN_CODE.BIN
6. PCI driver[A] 0A800h(42.00K) 056BEh(21.69K) 4247.bin
7. PCI driver 0C000h(48.00K) 07190h(28.39K) BA1216Q2.lom
8. VGA ROM[1] 10000h(64.00K) 07F87h(31.88K) 164_3104.DAT
9. Other(402E:0000) 01470h(5.11K) 00783h(1.88K) 164_3104.BIN
10. Flash ROM 0ABD5h(42.96K) 05D84h(23.38K) AWDFLASH.EXE
Total compress code space = 4B000h(300.00K)
Total compressed code size = 3D737h(245.80K)
Remain compress code space = 0D8C9h(54.20K)
** Micro Code Information **
Update ID CPUID | Update ID CPUID | Update ID CPUID | Update ID CPUID
------------------+--------------------+--------------------+-------------------
SLOT2 17 0F29 |
D:\Treiber\IPOX4M~1>
Server: Intel Pentium-M 1.60 GHz on DFI i855GME-MGF, 1 GB DDR-333 Kingston ValueRam, Yeon Yang 0420 Cube
Gaming: Intel Pentium-M 1.40GHz @ 1,87GHz on ASUS P4GPL-X, 512 MB DDR-433 Kingston HyperX, GeForce 6800GT, Lian LI PC-62
HTPC: Intel Pentium-M 1.50 GHz [passive] on Ipox 4MTI2H, 512 MB DDR-333 Infineon 3rd, Antec Aria Mini-Cube, VDR with dual DVB-T/-C
Gaming: Intel Pentium-M 1.40GHz @ 1,87GHz on ASUS P4GPL-X, 512 MB DDR-433 Kingston HyperX, GeForce 6800GT, Lian LI PC-62
HTPC: Intel Pentium-M 1.50 GHz [passive] on Ipox 4MTI2H, 512 MB DDR-333 Infineon 3rd, Antec Aria Mini-Cube, VDR with dual DVB-T/-C